201 PDF Dumps 2023 Exam Questions with Practice Test
Dumps for Free 201 Practice Exam Questions
For more info read reference:
F5-201 Official Certification Site
F5 201 (BIG-IP Administrator) Certification Exam is a globally recognized certification that validates the knowledge and skills required to manage and administer F5 BIG-IP products. BIG-IP Administrator Exam certification exam is designed for professionals who work with F5 BIG-IP products and want to demonstrate their expertise in managing and configuring these products.
NEW QUESTION # 143
A BIG-IP Administrator is working with a BIG-IP device and discovers that one of the Interfaces on a Trunk is DOWN.
What is the reason for this Interface status?
- A. There is NO transceiver installed on the Interface
- B. There is NO default route configured for this trunk
- C. The media speed of the interface has NOT been set
- D. The switch is NOT connected to the Interface
Answer: D
NEW QUESTION # 144
You have a pool of servers that need to be tested. All of the servers but one should be tested every 10 seconds, but one is slower and should only be tested every 20 seconds. How do you proceed?
- A. It cannot be done. All monitors test every five seconds.
- B. It can be done by assigning one monitor to the pool and a different monitor to the slower pool member.
- C. It can be done, but will require assigning monitors to each pool member.
- D. It cannot be done. All of the members of a pool must be tested at the same frequency.
Answer: B
NEW QUESTION # 145
Which statement is true concerning cookie persistence?
- A. Cookie persistence allows persistence even if the data are encrypted from client to pool member.
- B. Cookie persistence uses a cookie that stores the virtual server, pool name, and member IP address in clear text.
- C. If a client's browser accepts cookies, cookie persistence will always cause a cookie to be written to the client's file system.
- D. Cookie persistence allows persistence independent of IP addresses.
Answer: D
NEW QUESTION # 146
A BIG-IP Administrator creates a new VLAN on BIG-IP Cluster Member A and attaches an Interface to it. Although the Auto Config Sync is in place, the new VLAN does NOT show up on Cluster Member B.
What should the BIG-IP Administrator do to ensure the new VLAN is configured on each Cluster Member?
- A. Reset the Device Trust of the BIG-IP Cluster on either Cluster Member.
- B. Configure a Default Route for the new VLAN on Cluster Member A.
- C. Configure the new VLAN manually on Cluster Member B.
- D. Enable the Interface that is attached to the new VLAN on Cluster Member A.
Answer: C
NEW QUESTION # 147
A VLAN has the following objects configured:
Self-IP 10.10.10.100 with port lockdown set to Allow default
Virtual server 10.10.10.100:443 with UDP profile enabled
Virtual server 10.10.10.0/24 port forwarding virtual server
Global destination NAT forwarding 10.10.10.100 to internal server 172.168.10.100 Which object will process this request when https://10.10.10.100 is entered into a browser?
- A. virtual server 10.10.100/24 port o forwarding virtual server
- B. global destination NAT forwarding 10.10.10.100 to internal server 172.168.10.100
- C. virtual server 10.10.10.100.443 with UDP profile enabled
- D. self-IP 10.10.10.100 with port lockdown set to Allow default
Answer: D
NEW QUESTION # 148
Refer to the exhibit. The BIG-IP Administrator needs to avoid overloading any of the Pool Members with connections, when they become active.
What should the BIG-IP Administrator configure to meet this requirement?
- A. Same Priority Group to each member
- B. Action On Service Down to Reselect
- C. Slow Ramp Time to the Pool
- D. Different Ratio for each member
Answer: C
NEW QUESTION # 149
Refer to the exhibit.
During a planned upgrade lo a BIG-IP HA pair running Active/Standby, an outage to application traffic is reported shortly after the Active unit is forced to Standby Reverting the flower resolves the outage. What should the BIG-IP Administrator modify to avoid an outage during the next for over event?
- A. The Tag value on the Active device
- B. The Interface on the Standby device to 1.1
- C. The Tag voice on the Standby device
- D. The interface on the Active device to 1.1
Answer: C
NEW QUESTION # 150
A BIG-IP Administrator adds new Pool Members into an existing, highly utilized pool. Soon after, there are reports that the application is failing to load for some users. What pool level setting should the BIG-IP Administrator check?
- A. Action On Service Down
- B. Allow SNAT
- C. Slow Ramp Time
- D. Availability Requirement
Answer: C
Explanation:
Option ABC is a global configuration, has nothing to do with the new pool member, select D after excluding
NEW QUESTION # 151
A development team needs to apply a software fix and troubleshoot one of its servers. The BIG-IP Administrator needs to immediately remove all connections from the BIG-IP system to the back end server. The BIG-IP Administrator checks the Virtual Server configuration and finds that a persistence profile is assigned to it. What should the 8IG-IP Administrator do to meet this requirement?
- A. Set the pool member to a Disabled state and manually delete existing connections through the command line.
- B. Set the pool member to a Forced Offline state.
- C. Set the pool member to a Forced Offline state and manually delete easting connections through the command line.
- D. Set the pool member to a Disabled state.
Answer: C
NEW QUESTION # 152
A Standard Virtual Server configured for an application reports poor network performance. This application is accessed mainly from computers on the Internet.
What should the BIG-IP Administrator configure on the Virtual Server to achieve better network performance?
- A. Protocol Profile (Client) with f5-tcp-wan and Protocol Profile (Server) with f5-tcp-lan
- B. Protocol Profile (Client) with fS-tcp-lan and Protocol Profile (Server) with f5-tcp-wan
- C. Protocol Profile (Client) with f5-tcp-optimized
- D. Protocol Profile (Client) with f5-tcp-lan
Answer: A
NEW QUESTION # 153
A BIG-IP Administrator creates an HTTP Virtual Server using an iApp template. After the Virtual Server is created, the user requests to change the destination IP addresses. The BIG-IP Administrator tries to change the destination IP address from 10.1.1.1 to 10.2.1.1 in Virtual Server settings, but receives the following error:
The application service must be updated using an application management interface What is causing this error?
- A. The Application Service was NOT deleted before making the IP address change.
- B. The IP addresses used are NOT from the same subnet as the Self IP.
- C. The Application Services have Strict Updates enabled.
- D. The IP addresses are already in use.
Answer: C
Explanation:
Explanation
Strict Updates : Indicates whether the application service is tied to the template, so when the template is updated, the application service changes to reflect the updates.
NEW QUESTION # 154
A BIG-IP Administrator assigns the default http health monitor to a pool that has three members listening on port 80 When the administrator connects to each pool member via the CURL utility, two of the members respond with a status of 404 Not Found while the third responds with 200 OK. What will the pool show for member availability?
- A. Two members offline and one member online.
- B. Two members online and one member offline.
- C. All members online.
- D. All members offline.
Answer: C
NEW QUESTION # 155
Refer to the exhibit.
Which Pool Members are receiving traffic?
- A. serv1, serv3
- B. serv1, serv3, serv4
- C. serv1
- D. Serv1, serv2,serv3, serv4
Answer: B
NEW QUESTION # 156
The ICMP monitor has been assigned to all nodes. In addition, all pools have been assigned custom monitors. The pool is marked available. If a pool is marked available (green) which situation is sufficient to cause this?
- A. All of the pool member nodes are responding to the ICMP monitor as expected.
- B. Less than 50% of the pool member nodes responded to the ICMP echo request.
- C. All of the members of the pool have had their content updated recently and their responses no longer match the monitor.
- D. Over 25% of the pool members have had their content updated and it no longer matches the receive rule of the custom monitor. The other respond as expected.
Answer: D
NEW QUESTION # 157
Which IP address will the client address be changed to when SNAT automap is specified within a Virtual Server configuration.
- A. The floating self IP address on the VLAN where the packet leaves the system.
- B. The floating self IP address on the VLAN where the packet arrives on the system.
- C. It will alternate between the floating and noEl nfloating self IP address on the VLAN where the packet leaves the system so that port exhaustion is avoided.
- D. It will alternate between the floating and noElfnloating self IP address on the VLAN where the packet arrives on the system so that port exhaustion is avoided.
Answer: A
NEW QUESTION # 158
Which method is recommended for creating a new user from the CLI?
- A. Run f5adduser username' then 'f5passwd username' from bash or tmsh
- B. Run tmsh create auth user username prompt for password' from bash
- C. Run useradd username' then 'passwd username' from bash tmsh
- D. edit bigip.conf to add the new user and the user's clear-text password
Answer: B
Explanation:
Reference:
The f5adduser commands were removed and tmsh is the recommended way to create users.
https://support.f5.com/csp/article/K11677
NEW QUESTION # 159
Refer to the exhibit.
During a planned upgrade lo a BIG-IP HA pair running Active/Standby, an outage to application traffic is reported shortly after the Active unit is forced to Standby Reverting the flower resolves the outage. What should the BIG-IP Administrator modify to avoid an outage during the next for over event?
- A. The Tag value on the Active device
- B. The Interface on the Standby device to 1.1
- C. The Tag voice on the Standby device
- D. The interface on the Active device to 1.1
Answer: C
NEW QUESTION # 160
A BIGJP Administrator needs to load a UCS file but must exclude the license file. How should the administrator perform this task?
- A. From the GUI, select the UCS file and click restore
- B. From the CLI with command U tmsh load /$ys ucs <ucs filename> no-license
- C. From the GUI, select the UCS file, unchcck the license box, and click restore
- D. From the CLI with command(tmos)< tmsh load /sys ucs <ucs filename> no-license
Answer: B
NEW QUESTION # 161
Refer to the exhibit.
A BIG-IP Administrator configures the Virtual Server to pass HTTP traffic. Users report that they are unable to access the application What should the administrator do to resolve this issue?
- A. Reconfigure the Pool Members
- B. Change the Virtual Server name
- C. Reconfigure the Source Address
- D. Disable .he State
Answer: A
NEW QUESTION # 162
......
Check your preparation for F5 201 On-Demand Exam: https://www.lead2passed.com/F5/201-practice-exam-dumps.html
201 Dumps PDF And Certification Training: https://drive.google.com/open?id=1x2NUCpGSqZoa8tBMID6i2VfnX0JHJL8B
