100% Guaranteed Results 300-625 Unlimited 72 Questions [2021]
300-625 Dumps PDF - Want To Pass 300-625 Fast
NEW QUESTION 30
Refer to the exhibit.
Refer to the exhibit. A port channel has been configured between a Cisco MDS and a Cisco Fabric Interconnect switch. Which interface(s) in the port channel carry the control plane traffic?
- A. from interface fc1/10
- B. from interface fc1/9
- C. per packet, balanced between interfaces fc1/9 and fc1/10
- D. per flow, balanced between interfaces fc1/9 and fc1/10
Answer: C
NEW QUESTION 31
A storage network engineer is implementing SAN telemetry for a SAN infrastructure using Cisco DCNM for SAN. Which command is used to check the session status for telemetry operation?
- A. show telemetry transport
- B. show telemetry pipeline stats
- C. show analytics system-load
- D. show telemetry control stats
Answer: A
Explanation:
Section: Management and Monitoring
NEW QUESTION 32
A storage administrator is enabling DH-CHAP for the first time on a Fibre Channel fabric.
Which condition must the administrator consider while configuring this feature?
- A. NTP must be configured on all devices or the configuration fails.
- B. The MD5 hash must be used if TACACS+ or RADIUS authentication for FCSP is enabled.
- C. All switches on the fabric must be configured for the same password.
- D. Enabling DH-CHAP protocol feature is unsupported on FCIP interfaces.
Answer: B
NEW QUESTION 33
After a subordinate switch requests a domain ID form a principal switch, the requested domain ID becomes the runtime domain ID, and all interfaces on the affected VSAN are isolated. What is a solution to the issue?
- A. Configure IVR NAT on the affected VSAN.
- B. Enable the FICON feature on the affected VSAN.
- C. Configure a static domain on the subordinate switch and reboot the switch.
- D. Add the received ID to the allowed list.
Answer: D
NEW QUESTION 34
Which configuration is always required when running the setup utility on a Cisco MDS 9000 Series Switch?
- A. administrator password
- B. management IP address
- C. active NTP server
- D. active default gateway
Answer: A
NEW QUESTION 35
A network engineer must run a core Cisco Nexus 9500 Series Switch as a POAP server for all top-of-rack Cisco Nexus switches. Which two network functions must run to provide the POAP service? (Choose two.)
- A. TFTP
- B. DNS
- C. BOOTP
- D. PXE
- E. DHCP
Answer: A,E
NEW QUESTION 36
Which item is a component of Cisco DCNM?
- A. Cisco DCNM for SAN and Cisco DCNM for LAN
- B. Cisco DCNM for Cisco UCS Manager
- C. Cisco DCNM FabricPath license
- D. Cisco DCNM for B- and C-Series servers
Answer: A
NEW QUESTION 37
Which component is initially responsible for loading the kickstart image on Cisco MDS Switches?
- A. BASH
- B. ROMMON
- C. BIOS
- D. NX-OS
Answer: D
Explanation:
Section: Deployment
NEW QUESTION 38
Which benefit of upgrading to the Cisco DCNM server-based advanced feature license for a Cisco MDS switch is correct?
- A. The license can be reassigned when the switch is replaced with a Cisco Nexus switch
- B. The license can be assigned to either server MAC address or switch serial number
- C. The license can be reassigned when a switch is replaced with a newer version within the same product family
- D. An unlimited number of devices can be added to the list of licensed devices
Answer: C
NEW QUESTION 39
Refer to the exhibit.
A storage network engineer gets remote access to two Cisco MDS 9000 Series Switches with an ISL trunk and receives several log messages. Which set of actions resolve the problem while least affecting service?
- A. 1. Explicitly import zone set Zoneset10-A on MDS-B using the zoneset import interface import fc1/11 vsan 10 command.
2. Activate the zone set Zoneset10-A. - B. 1. Add :11:11:11:11:11:11:11:13 pwwn in zone Server11 and activate Zoneset10-A on MDS-A.
2. shut/no shut interface fc1/11 on MDS-A. - C. 1. Add :11:11:11:11:11:11:11:13 pwwn in zone Server11 and activate Zoneset10-A on MDS-A.
2. Remove VSAN 10 from the allowed VSAN range of interface fc1/11 on MDS-A and add it back in the range. - D. 1. Deactivate zone set Zoneset10-A on MDS-A.
2. shut/no shut interface fc1/11 on MDS-A.
Answer: B
Explanation:
Section: MDS Troubleshooting
NEW QUESTION 40
A storage administrator is enabling DH-CHAP for the first time on a Fibre Channel fabric. Which condition must the administrator consider while configuring this feature?
- A. NTP must be configured on all devices or the configuration fails.
- B. The MD5 hash must be used if TACACS+ or RADIUS authentication for FCSP is enabled.
- C. All switches on the fabric must be configured for the same password.
- D. Enabling DH-CHAP protocol feature is unsupported on FCIP interfaces.
Answer: B
Explanation:
Section: Implementation
NEW QUESTION 41
An engineer is configuring a SAN environment and attempts to activate a zoneset, but a lock is held by another user. Which argument does the engineer use to clear the lock from the zoning database configuration?
- A. abort
- B. force
- C. commit
- D. clear
Answer: D
Explanation:
Section: Implementation
NEW QUESTION 42
Which EtherType is used by the FCoE Initialization Protocol?
- A. 0x8914
- B. 0x8906
- C. 0xxfc0e
- D. 0x8913
Answer: A
NEW QUESTION 43
Which action must be performed to deactivate a VSAN without losing its configuration?
- A. Isolate it.
- B. Suspend it.
- C. Rename it.
- D. Delete it.
Answer: B
Explanation:
Section: Implementation
NEW QUESTION 44
A storage administrator is enabling DH-CHAP for the first time on a Fibre Channel fabric. Which condition must the administrator consider while configuring this feature?
- A. NTP must be configured on all devices or the configuration fails.
- B. The MD5 hash must be used if TACACS+ or RADIUS authentication for FCSP is enabled.
- C. All switches on the fabric must be configured for the same password.
- D. Enabling DH-CHAP protocol feature is unsupported on FCIP interfaces.
Answer: A
NEW QUESTION 45
Two stable fabrics have overlapping domains. After a switch from the first domain is joined to a switch from the second domain, both switches become isolated. What caused the problem?
- A. The rcf-reject option is enabled on the interfaces.
- B. The autoreconfigure option is enabled on both switches.
- C. The rcf-reject option is disabled on the interfaces.
- D. The autoreconfigure option is disabled on both switches.
Answer: D
Explanation:
Section: MDS Troubleshooting
Explanation/Reference:
NEW QUESTION 46
A storage administrator is configuring inter-VSAN routing on a fabric that contains duplicate domain IDs. Which feature must be configured to ensure continued operation?
- A. virtual domains
- B. IVR NAT
- C. auto topology
- D. transit VSANs
Answer: B
NEW QUESTION 47
......
Updated Verified 300-625 Q&As - Pass Guarantee: https://www.lead2passed.com/Cisco/300-625-practice-exam-dumps.html
