Valid 300-625 Exam Q&A PDF 300-625 Dump is Ready (Updated 72 Questions)
Exam Questions and Answers for 300-625 Study Guide
NEW QUESTION 13
Refer to the exhibit.
Refer to the exhibit. A user who is logged in as an operator cannot update the zoneset. What is the cause of this issue?
- A. Hard zoning is enabled
- B. Merge control is disabled
- C. The fabric is locked by admin on another switch
- D. The fabric is locked by admin on switch-2
- E. The switch has a conflicting domain ID
Answer: C,E
NEW QUESTION 14
Refer to the exhibit.
Which configuration change improves the ability of the link to recover from frame loss?
- A. Disable PMTU discovery.
- B. Increase the send buffer size to 15000 KB.
- C. Enable selective acknowledgment.
- D. Increase the reset timeout.
Answer: C
NEW QUESTION 15
What does an unlicensed DCNM SAN fail to display?
- A. Fibre Channel, FCoE, and iSCSI topologies
- B. historical performance monitoring
- C. real-time performance monitoring
- D. events and fault management
Answer: B
Explanation:
Section: Management and Monitoring
NEW QUESTION 16
Which configuration is always required when running the setup utility on a Cisco MDS 9000 Series Switch?
- A. management IP address
- B. active NTP server
- C. administrator password
- D. active default gateway
Answer: C
Explanation:
Section: Implementation
NEW QUESTION 17
Refer to the exhibit.
Refer to the exhibit. An engineer is configuring Inter-VSAN routing for two Cisco MDS switches. The FSPF cost between the switches is 500, and the Cisco MDS core virtuahzes an IVR NAT domain as shown. Which statement about the topology is correct?
- A. The MDS-Core simulates an IVR NAT and increases the cost to 501.
- B. The MDS-Core simulates an IVR NAT. and the FSPF cost is 500.
- C. The MDS-Core simulates an IVR NAT and increases the cost to 600.
- D. The MDS-Core simulates an IVR NAT and decreases the cost to 400.
Answer: B
NEW QUESTION 18
Which EtherType is used by the FCoE Initialization Protocol?
- A. 0*8913
- B. 0*8914
- C. 0*xfc0e
- D. 0*8906
Answer: B
NEW QUESTION 19
What is the function of the 0xFFFFFC address in a Fibre Channel fabric?
- A. management server
- B. name server
- C. fabric controller
- D. time server
Answer: B
Explanation:
Section: Implementation
Explanation
NEW QUESTION 20
After user account attributes are modified in Cisco NX-OS, when do changes to the user's session attributes take effect?
- A. at the scheduled time
- B. when the user logs out of a session
- C. immediately
- D. when the user creates a new session
Answer: D
NEW QUESTION 21
Which configuration is needed to enable manual ESP mode for Fibre Channel TrustSec on Cisco MDS switches?
- A. MDS(config)# interface fc 1/1
MDS(config-if)# fcsp mode gem
MDS(config-if-fcsp)# fcsp esp manual - B. MDS(config)# interface fc 1/1
MDS(config-if)# fcsp esp manual - C. MDS(config)# interface fc 1/1
MDS(config-if)# fcsp esp manual
MDS(config-if-esp)# mode gem - D. MDS(config)# fcsp esp manual
Answer: C
NEW QUESTION 22
A network engineer is configuring a Cisco MDS switch for FCoE. Which two conditions must be considered during the implementation phase? (Choose two.)
- A. The QoS policy must be identical to other Cisco FCoE switches in the network.
- B. On Cisco MDS switches, system-defined class maps for class-FCoE and class-default are enabled but can be deleted.
- C. VLAN 1 or the native VLAN can be mapped to an FCoE VSAN.
- D. On the Cisco MDS, the MTU is set equal to 2112.
- E. FCoE is already enabled on a Cisco MDS switch.
Answer: A,E
NEW QUESTION 23
Refer to the exhibit.
The san-user must configure FSPF on the VSAN 500, but fails. An operator with network administrative rights must authorize the san-user to perform this work. Which configuration must the operator apply?
- A. MDS-A(config)# role name sangroup
MDS-A(config-role)# rule 2 permit config feature vsan - B. MDS-A(config)# role name sangroup
MDS-A(config-role)# vsan policy deny
MDS-A(config-role-vsan)# permit vsan 500 - C. MDS-A(config)# role name sangroup
MDS-A(config-role)# no rule 2 - D. MDS-A(config)# role name sangroup
MDS-A(config-role)# rule 4 permit config feature fspf
Answer: B
NEW QUESTION 24
Two stable fabrics have overlapping domains. After a switch from the first domain is joined to a switch from the second domain, both switches become isolated. What caused the problem?
- A. The rcf-reject option is enabled on the interfaces.
- B. The autoreconfigure option is disabled on both switches.
- C. The autoreconfigure option is enabled on both switches.
- D. The rcf-reject option is disabled on the interfaces.
Answer: B
NEW QUESTION 25
Drag and drop the mechanisms of Cisco Secure Boot from the left into the correct order on the right.
Answer:
Explanation:
NEW QUESTION 26
A storage network engineer is implementing disk-array data replication between two SAN environments in two different data centers not connected via Fibre Channel. Which SAN switch feature must be implemented?
- A. VSAN scoping
- B. zoning merge over LAN
- C. IVR
- D. FCIP
Answer: D
NEW QUESTION 27
Refer to the exhibit.
A network engineer must configure the SAN telemetry streaming feature to stream statistics form a Cisco MDS
9000 Series Switch to two external receivers with the IP addresses 192.168.1.4 and 192.168.1.5. Which two configurations accomplish this configuration? (Choose two.)
- A. Add dst-grp 300 under subscription 200.
- B. Add dst-grp 100 under subscription 200.
- C. Add dst-grp 200 under subscription 100.
- D. Add IP address 192.168.1.5 port 50005 protocol gRPC encoding GPB under destination-group 100.
- E. Add IP address 192.168.1.5 port 50005 protocol gRPC encoding GPB under destination-group 300.
Answer: C,D
Explanation:
Section: Management and Monitoring
NEW QUESTION 28
A storage network engineer is implementing disk-array data replication between two SAN environments in two different data centers not connected via Fibre Channel. Which SAN switch feature must be implemented?
- A. VSAN scoping
- B. zoning merge over LAN
- C. IVR
- D. FCIP
Answer: D
Explanation:
Section: Implementation
NEW QUESTION 29
A network engineer is configuring a Cisco MDS switch for FCoE. Which two conditions must be considered during the implementation phase? (Choose two.)
- A. The QoS policy must be identical to other Cisco FCoE switches in the network.
- B. VLAN 1 or the native VLAN can be mapped to an FCoE VSAN.
- C. On the Cisco MDS, the MTU is set equal to 2112.
- D. FCoE is already enabled on a Cisco MDS switch.
- E. On Cisco MDS switches, system-defined class maps for class-FCoE and class-default are enabled but can be deleted.
Answer: A,E
NEW QUESTION 30
Which feature on MDS platforms ensures that the code that is running on the hardware platform is authentic and unmodified, while also validating the BIOS to eliminate any rootkits.
- A. Secure Unique Device Identifier
- B. Cisco Secure Boot
- C. UEFI Secure Boot
- D. BIOS Secure Boot
Answer: B
NEW QUESTION 31
Refer to the exhibit.
Refer to the exhibit. Which command is used to determine which switch has the lock?
- A. show fcs ie vsan
- B. show zoneset active
- C. show flogi database
- D. show zont status
Answer: D
NEW QUESTION 32
After a subordinate switch requests a domain ID form a principal switch, the requested domain ID becomes the runtime domain ID, and all interfaces on the affected VSAN are isolated.
What is a solution to the issue?
- A. Configure a static domain on the subordinate switch and reboot the switch.
- B. Configure IVR NAT on the affected VSAN.
- C. Enable the FICON feature on the affected VSAN.
- D. Add the received ID to the allowed list.
Answer: D
NEW QUESTION 33
......
Certification dumps - CCNP Data Center 300-625 guides - 100% valid: https://www.lead2passed.com/Cisco/300-625-practice-exam-dumps.html
